Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Inspection for Coral Springs Homeowners
A chimney can look fine from the living room and still be hiding a cracked flue tile, a failed crown, or creosote packed two inches deep. That’s the problem an inspection solves. It’s also the reason we diagnose before we recommend anything: you get photos and camera footage you can see yourself, not a verbal claim about what’s wrong inside a shaft you’ll never look down. Our technicians have up to 10 years of experience, and Carrington Chimney Sweep handles the sweep, the repair, and the formal inspection as one system, so nothing gets missed in a handoff. We answer 24/7 at (844) 834-5492, and we can often get to Coral Springs inspections the same day. No pressure, no guessing. Just what your chimney actually needs.
Fireplace Inspection
Fireplace Inspection is the close-up look at the firebox, damper, smoke shelf, and the first stretch of flue above the fire – the parts you can’t see when you’re standing in front of a fire. You need one before the first burn of the season, after any chimney fire, and whenever smoke rolls into the room instead of up the flue. We open the firebox, check the damper for a clean seal, inspect the brick and mortar joints for spalling, and confirm the smoke chamber transitions without gaps. Where the firebox refractory has worn thin, we can resurface with HeatShield rather than rebuild. A fireplace-level inspection typically runs $99-$175 depending on how much of the firebox has to be accessed.
Firebox and Damper Checks
The damper is the most-used moving part in the whole system and the easiest to overlook. We test it open and closed and check that the frame isn’t warped or rusted shut. A damper that won’t seal sends heat straight up the flue when the fireplace is idle.
Smoke Chamber and Refractory
The smoke chamber is the sloped transition between the firebox and the flue, and it collects creosote in corners a brush can’t always reach. We inspect its parging for cracks and rough spots that catch soot. Loose or crumbling refractory brick in the firebox floor gets flagged before it becomes a bigger repair.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Inspection Services
Chimney Inspection Services cover the whole stack: crown, masonry or siding, cap, flue liner, firebox, and the connections to appliances. You need them annually if you burn wood, before buying or selling a home, and after any storm that knocks debris or a cap loose. Carrington Chimney Sweep runs the inspection as a standalone service when you need documentation for a real estate transaction, an insurance file, or a safety record, and we’ll write up findings clearly enough to hand to anyone. A standard inspection is typically $99-$250 depending on the level and how much of the system gets camera work. Every recommendation comes with a photo you can see for yourself.
Standalone and Real Estate Inspections
Not every call needs a sweep attached. When a buyer or an insurer needs a formal record of condition, we inspect and document without selling additional work. The report states what’s sound, what’s worn, and what can safely wait.
Crown, Cap, and Chase
The crown is the concrete or mortar cap on top that sheds water away from the flue, and it’s where most water intrusion starts. We check for cracks and separation from the flue tile. If the cap is failing or missing, we install Gelco or Famco caps matched to the flue size.
Chimney Flue Inspection
Chimney Flue Inspection is the check of the liner itself, from the top down and the bottom up, to confirm the flue is continuous, correctly sized, and free of cracks, gaps, or heavy glaze. You need it if you’ve had a chimney fire, if the liner is clay tile of unknown condition, or if a new appliance was connected without documenting the flue. We run a camera the length of the flue and look for offset tiles, missing mortar joints, and gaps at the thimble where a stove or furnace ties in. A flue inspection typically runs $150-$350 depending on access and whether camera work is included. If the flue is pitted but structurally sound, HeatShield resurfacing can often restore it without a full reline.
Liner Condition and Sizing
A liner that’s too large for the appliance cools the exhaust too fast and lets creosote condense on the walls. Too small and the draft suffers. We measure the flue and match it against what’s actually venting into it.
Thimble and Appliance Connections
Where a wood stove or insert connects, the thimble joint is a common failure point. We check that the connector pipe seats fully and that no gap lets exhaust into the chase. Correct pipe and venting components from Olympia Chimney or DuraFlex close those gaps properly.
Chimney Fire
Chimney Fire damage is what an inspection after the fact is looking for: cracked tiles, warped dampers, heat-stressed mortar, and creosote that reignited higher in the flue. You need an inspection after any chimney fire, even a small one that seemed to go out on its own, because the heat can crack a liner without you hearing anything. We inspect the full flue for thermal damage, test the damper, and check the cap and crown for heat distortion. Post-fire inspections typically run $175-$400 depending on how much camera work and liner testing is needed. If damage is limited to surface pitting, HeatShield can rebuild the liner face; if tiles are cracked through, a DuraFlex liner is the right fix. This is not a spot to open a fire until a professional confirms the flue is sound.
Recognizing the Aftermath
Puffy, honeycombed creosote and a warped damper are telltale marks of a fire that burned hotter than a normal flue does. We document what we find so you know exactly what you’re dealing with. The camera does the talking.
Preventing the Next One
Most chimney fires start with creosote buildup from restricted draft or unseasoned wood. Regular sweeping and keeping the flue clear is the real prevention. We’ll tell you honestly how often your system needs attention based on how you burn.
Level 2 Chimney Inspection
Level 2 Chimney Inspection is the full inspection that includes camera work through the flue and a look at accessible portions of the chimney exterior, attic, and crawlspace connections. You need it when you buy or sell a home, after a chimney fire or earthquake, after a major storm, or when switching to a different appliance or fuel type. We run the camera, inspect the accessible chase, check clearances to combustibles, and document everything with photos. A Level 2 inspection typically runs $250-$450 depending on the number of flues and how much of the system has to be accessed. It’s the level most real estate transactions and insurers ask for, and it gives you a defensible record of condition.
When Level 2 Is Required
A property transfer is the most common trigger, but a new insert or a change in fuel qualifies too. If the system’s history is unknown, the camera answers the question the eye can’t. We write up findings so a buyer, seller, or adjuster can act on them.
Documentation You Can Hand Off
The report includes photos of the flue, the firebox, the crown, and any areas of concern, with clear notes on what needs work and what can wait. It’s built to travel into a transaction file. No jargon, no upsell language.
Chimney Leak
Chimney Leak diagnosis is the check for water getting into the chimney or the house around it, which usually shows up as a damp stain on the ceiling, water in the firebox, or a musty smell after rain. You need it whenever you see staining, efflorescence on the brick, or rust on the damper or firebox. We inspect the crown, the flashing where the chimney meets the roof, the cap, and the flue tile joints, since water can track down any of those paths. Leak diagnosis typically runs $125-$300 depending on access and how high the roofline sits. The fix is often a new crown, re-flashing, or a properly fitted Gelco cap, and we’ll show you the evidence before recommending any of it.
Tracing the Path
Water rarely enters where the stain appears, so we work from the top down, checking each potential entry in sequence. The camera helps where the flue has to be looked at internally. Once we locate the source, the repair gets scoped to that, not to a list of unrelated add-ons.
Crown and Flashing Repairs
A cracked crown lets water sit against the flue tile and freeze into the masonry. Re-flashing at the roof joint closes the second common path. Both are bread-and-butter repairs, and both get finished with correctly matched cap and venting hardware.
Chimney Camera Inspection
Chimney Camera Inspection uses a closed-circuit video system run down the flue to see the interior of the liner without dismantling anything. You need it for a Level 2 inspection, a home sale, a liner of unknown age, or any suspected damage from a chimney fire. We feed the camera from the top and record the whole run, then review the footage with you so you can see the cracks, gaps, or buildup in the liner yourself. A camera inspection typically runs $150-$350 depending on flue length and the number of flues examined. The footage is yours to keep, and it’s the basis for whatever repair, resurfacing, or relining we recommend – or for the recommendation to do nothing.
What the Camera Reveals
Cracked tiles, offset joints, gaps at the thimble, and heavy glaze all show up on camera in ways a brush and a flashlight miss. The footage is your evidence, not a sales tool. If the liner is sound, the report says so.
Top-Down and Bottom-Up Views
We run the camera from the top for a clear view of the crown and flue transition, and from the bottom where the appliance connection needs closer inspection. Between the two, nothing in the flue goes unexamined. The recorded session becomes part of your file.
Brands We Service
We work with the professional-tier products that match the components already inside your chimney. HeatShield resurfacing is one we use often, since it rebuilds a worn flue face without a full reline, and we know exactly where the application holds and where it doesn’t. Gelco and Famco caps and venting components matter too, because a repair finished with the wrong cap or connector just creates the next problem. We fit them to the flue, not to whatever is on the shelf.
Olympia Chimney and DuraFlex enter the picture on liner and venting replacement, and we install them to the system’s actual dimensions, not a one-size guess. The goal is a liner and a termination that perform like the originals spec’d them. Whether you have HeatShield, Gelco, Olympia Chimney, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke rolling into the room. A fireplace that smokes when you open the glass or on a cold start may be a blocked flue or a smoke chamber problem. It also points to draft issues that worsen with buildup. Don’t keep burning through it – let us look.
- Creosote that looks puffy or glazed. Puffy, honeycombed, or shiny glazed creosote is the kind that fuels a chimney fire. It means the flue is overdue and needs sweeping before the next burn.
- A water stain on the ceiling near the chimney. Staining, efflorescence, or water in the firebox points to a leak at the crown, flashing, or cap. Left alone, water rots the framing and the masonry.
- Rust or a stuck damper. A rusted damper, warped firebox, or corroded connector pipe is a sign of ongoing moisture or heat damage. It’s a small fix now and a bigger repair if ignored.
- A sour, smoky smell after rain. That odor usually means moisture is mixing with creosote somewhere in the flue. A camera inspection locates it fast, and the fix is usually straightforward.
Our Process, Step by Step
- 1
We talk first. A quick conversation about what you’re seeing, how often you burn, and whether the home is for sale or an insurance file is involved tells us what level of inspection you actually need. No inspection gets upsold past what the situation calls for.
- 2
We protect the room. Drop cloths go down, the work area is sealed, and we set up the equipment before any inspection begins. Nothing in the room moves without your say-so.
- 3
We inspect from the top down and the bottom up. The crown, cap, and flue get looked at from the roof, and the firebox, damper, and appliance connections get checked from inside. A closed-circuit camera runs the flue so the liner is seen, not assumed.
- 4
We show you what we found. The camera footage and photos are reviewed with you directly. We point out the real problems, note what’s still sound, and say plainly when work can safely wait.
- 5
We put it in writing. The written estimate sets the price, and it’s free. Any follow-on repair uses the right product – HeatShield for resurfacing, Gelco or Famco for caps, DuraFlex or Olympia Chimney for liners – matched to what’s actually there.
How Much Does Chimney Inspection Cost in Coral Springs?
Chimney inspection in Coral Springs typically runs $99 for a basic level-one look up to $450 for a full Level 2 with camera work across multiple flues. Most homeowners land in the $150-$350 range depending on what’s involved.
The spread comes from a few real factors. Older homes with clay tile liners that need camera verification cost more to inspect than a newer, single-flue setup. Multiple flues, an insert or wood stove connection, and roof access all add time. A post-fire inspection is heavier work because the liner has to be tested for heat damage, not just looked at.
The biggest cost driver is the level of inspection you need, and the biggest way to avoid overpaying is to not pay for a Level 2 when a level one answers the question. That’s why we ask what prompted the call before we quote. If you’re buying or selling a home, or an insurer asked for documentation, Level 2 is the right level. If you just want to know the fireplace is safe to light, a lower-level inspection may cover it. Either way, the estimate is free and the written estimate sets the final price.
Every inspection includes the camera footage and photo report, so nothing is recommended without evidence you can see for yourself. And we’ll tell you when there’s nothing to fix – a sound chimney needs a report, not a repair. Call (844) 834-5492 for an exact quote.
Coral Springs sits inland from the coast and its winters are mild, which means most of the wear on a chimney here comes from rain and humidity rather than hard freezing. Water finding its way past a worn crown or a failed flashing does more damage over a few rainy seasons than a cold snap would, and our inspection focuses there. If you have neighbors in Carrington Chimney Sweep territory, the same rainy-season pattern shows up across the area.
Our Service Area Near Coral Springs
We serve Coral Springs and the surrounding communities, including Margate, Parkland, Tamarac, North Lauderdale, and Coconut Creek, plus Highland Beach, Seminole Manor, San Castle, and Hypoluxo. When you call, we’ll confirm a time and let you know when a technician can reach you. Dispatch runs Sunday through Friday, 7am to 7pm, with fast same-day scheduling where it’s available. Call (844) 834-5492 and we’ll get your inspection booked.
Serving Coral Springs, FL – Our Local Coverage Area
We serve Coral Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Inspection in Coral Springs
A chimney inspection is a structured look at the full chimney system – crown, cap, flue, firebox, damper, and appliance connections – to confirm it’s safe and sound. It ranges from a visual level-one check to a Level 2 with camera work through the flue. It’s different from a sweep: an inspection diagnoses condition, a sweep cleans creosote. Call (844) 834-5492 and we’ll tell you which one your situation needs.
A level-one inspection usually takes about 45 minutes to an hour, while a Level 2 with camera work runs one to two hours depending on the number of flues and access. Add time if an insert or stove connection needs close inspection. We’ll give you a better estimate when we book, after we know what’s in the system. Call (844) 834-5492 to schedule.
Typical pricing in Coral Springs is $99-$250 for a standard inspection and $250-$450 for a Level 2 with camera work, with most jobs landing in the $150-$350 range. Flue count, appliance connections, and roof access are what move the number. The estimate is free and the written estimate sets the final price. Call (844) 834-5492 for an exact quote.
Yes – we install and service HeatShield resurfacing, Gelco and Famco caps and venting, and DuraFlex and Olympia Chimney liner systems. These are the professional-tier components we work with because they match the durability of what’s already in your chimney. If resurfacing can save a worn flue without a full reline, HeatShield is often the right call. Call (844) 834-5492 to talk through what your system has.
Same-day inspection is often possible depending on the schedule – call and we’ll confirm. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm. Call (844) 834-5492.
Our installations are backed by a satisfaction guarantee, and the products we use – HeatShield, Gelco, Famco, DuraFlex, Olympia Chimney – carry their own documented performance histories. If something we installed fails, we stand behind the work. Call (844) 834-5492 and we’ll walk you through what’s covered.
Clear access to the fireplace, the attic hatch, and the roofline if you have one, and hold off on a fire for at least 24 hours before we arrive. Make a note of how often you burn and whether you’ve seen smoke, water, or rust – it helps us target the inspection. Our technicians have up to 10 years of experience, so we’ll handle the rest. Call (844) 834-5492 to book.
Schedule Your Chimney Inspection Service in Coral Springs Today
Don’t wait for the first cold snap to find out what’s in your flue. Book a chimney inspection in Coral Springs with Carrington Chimney Sweep and get camera footage, a clear photo report, and an honest recommendation you can act on – or decide to hold. We answer 24/7, and fast dispatch runs 7am to 7pm, Sunday through Friday. Call (844) 834-5492 for a free, no-obligation estimate.
Written by the team at Carrington Chimney Sweep.