Sweep & inspection
Caps & crowns
Flue relining
Masonry repair
Gas fireplace serviceLevel 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Trusted Chimney Repair for Coral Springs Homeowners
Most chimney problems in Coral Springs don’t announce themselves. A cracked crown, a rusted cap, or a liner that’s lost its seal usually sits quiet until a rainy season forces water into the flue and you notice a stain on the ceiling or a smoky smell that won’t clear. That’s the moment people call us, and it’s exactly the moment we’re built for. Our technicians have up to 10 years of experience diagnosing flue and masonry issues specific to South Florida homes, where heat, humidity, and heavy summer rain do their own kind of damage over time.
We work as a specialist shop, not a generalist with a brush. Sweep, repair, and inspection run as one system under Carrington Chimney Sweep, so nothing falls between contractors. Same-day repair is often available when you call early. Reach us at (844) 834-5492.
Chimney Cap Installation
Chimney Cap Installation means fitting a correctly sized cap and spark screen over the flue opening to keep rain, animals, and debris out. You need it when a flue is open to the sky, when a home has just been built or re-roofed, or when a prior cap has gone missing. Carrington Chimney Sweep installs Gelco and Famco caps sized to the actual flue, not a generic hardware-store unit that rattles loose in a storm. Typical cap installation runs $250-$550 depending on flue count, cap style, and how the crown needs to be prepared for a proper mount. Every job starts with a measurement and a written estimate.
Why Cap Fit Matters
A cap that’s too small or poorly anchored lets water sheet down the flue and invites birds and squirrels to nest. A correctly fitted cap sheds rain away from the crown and screens sparks without choking draft. We match the cap to the flue’s actual dimensions rather than forcing a universal size.
Single-Flue and Multi-Appliance Setups
Homes with a fireplace plus a furnace or water heater flue need separate caps at separate heights. Each opening gets its own measured cap so no flue is left uncovered. We check clearance between flues while we’re up there and flag anything that would let one cap interfere with another.
Styles & brands we work with
- Sweep & inspection
- Caps & crowns
- Flue relining
- Masonry repair
- Gas fireplace service
Chimney Cap Replacement
Chimney Cap Replacement is the removal of a damaged, rusted, or storm-loosened cap and the fitting of a new one that seals the flue properly again. You need it when the existing cap is bent, missing its screen, or has started to rust through, which happens faster in humid South Florida air than most homeowners expect. Carrington Chimney Sweep replaces caps with Gelco or Olympia Chimney components chosen to match your flue size and the way your chimney is built. Chimney cap replacement typically runs $250-$550, with the final figure set by your written estimate based on cap type and flue configuration.
Spotting a Cap That Has Failed
A cap that’s tilted, rusted at the seams, or missing part of its screen has stopped doing its job. Once the screen is gone, debris and wildlife get in, and once the top plate rusts, water finds its way down. Replacing it early is far simpler than cleaning up after a flue full of nests.
Choosing the Right Replacement
We size the new cap to the flue opening and check that it clears the crown without trapping moisture against the masonry. Olympia Chimney and Gelco both make caps built for long service in humid climates. The goal is a snug, secure fit that stays put through summer storms.
Chimney Liner Installation
Chimney Liner Installation is the fitting of a new flue liner inside the chimney to restore a safe, code-compliant path for smoke and gases. You need it when the existing clay tile liner is cracked, spalling, or missing, or when an appliance is venting into an unlined flue. Carrington Chimney Sweep installs DuraFlex liner systems, the professional-grade stainless product line contractors and certified chimney engineers specify. Typical liner installation runs $1,800-$4,500 depending on flue height, liner diameter, and whether the chimney needs prep work first. The written estimate sets the final price after we’ve run a camera down the flue.
When Resurfacing Beats Replacement
Not every damaged liner needs full replacement. HeatShield resurfacing restores liner integrity from the inside when the damage is moderate, and it usually costs less than a full reline. We diagnose first with a camera, then recommend resurfacing or replacement based on what the footage actually shows.
What Installation Involves
A liner job starts with a thorough cleaning and a camera inspection of the full flue. We then size and insulate the new liner, feed it down, and connect it to the appliance collar and the top plate. When we’re done, you get a photo record of the finished work.
Chimney Flashing Repair
Chimney Flashing Repair addresses the metal seal where the chimney meets the roof, the most common source of chimney leaks. You need it when you see water stains near the chimney, rusted or lifted flashing, or daylight at the roofline, especially after a heavy rain. Carrington Chimney Sweep reseals, re-laps, or replaces flashing with Copperfield specialty components that hold up to the wind-driven rain this region gets. Chimney flashing repair typically runs $300-$800 depending on roof pitch, flashing material, and how much of the existing setup can be reused. Your written estimate sets the final figure.
Why Flashing Fails Here
Heavy summer rain and strong storm gusts work at the flashing seams until caulk and old sealant give way. Once water gets behind the flashing, it travels down into the attic and framing rather than showing up right away at the chimney. Catching it early keeps the repair small.
Sealing Versus Rebuilding the Joint
Sometimes a simple re-caulk and re-lap solves the leak. Sometimes the flashing has pulled far enough that the joint needs to be rebuilt with new metal. A camera check of the interior gives us the evidence to tell you which one you’re facing.
Chimney Crown Repair
Chimney Crown Repair fixes the concrete or masonry cap at the very top of the chimney that sheds water away from the flue. You need it when the crown is cracked, crumbling, or has pulled away from the flue, which lets rain seep in and start breaking down the masonry below. Carrington Chimney Sweep repairs crowns with proper bonding and a slope that keeps water moving off the top. Chimney crown repair typically runs $350-$900 depending on the size of the crown, the extent of the cracking, and whether the whole crown needs rebuilding. The written estimate you receive sets the final price.
Cracks That Signal Real Trouble
Hairline cracks in a crown widen over time as water gets in and expands with the heat. Once the crown no longer seals the top of the chimney, water runs down the inside of the flue and through the masonry. A repaired crown closes that path at the source.
Rebuilding Versus Sealing a Crown
Small cracks can be sealed. A crown that’s broken through or separated from the flue usually needs rebuilding to hold its slope. We check the whole crown surface before recommending which approach fits your chimney.
Chimney Repair Companies
Chimney Repair Companies vary widely in what they actually do, and choosing the right one is worth more than a few dollars saved on the bid. You need a company that can sweep, repair, and inspect the whole system without handing you off to a second crew mid-job. Carrington Chimney Sweep runs all three under one standard of work, with HeatShield resurfacing, DuraFlex liners, and Gelco caps in the mix. Work across these categories typically runs from $250 for a simple cap to $4,500 for a full liner, set per job by your written estimate. We diagnose first, so the repair we recommend is the repair you actually need.
Questions to Ask Before Booking
Ask what product brands the company uses, whether they run a camera inspection before quoting, and whether sweep, repair, and inspection are handled by the same crew. Vague answers on any of those are worth taking seriously. A specialist can tell you right away what they stock and what they specify.
Why We Use Named Materials
We work with professional-tier brands because their performance is documented and their parts are made to last in real flues. Anonymous bulk-supply parts may cost less up front and fail sooner. What you get in writing names the materials, so you know exactly what went in.
Chimney Masonry Repair
Chimney Masonry Repair restores the brick, mortar joints, and surrounding structure of the chimney when weather or age has taken a toll. You need it when you see crumbling mortar, loose bricks, or white staining on the exterior, or when a repair up top has revealed that the masonry itself is failing. Carrington Chimney Sweep handles masonry repair as part of the complete repair picture, not as an isolated patch. Chimney masonry repair typically runs $500-$2,500 depending on the scope, whether it’s spot joint work or a larger rebuild section. Your written estimate sets the total after we’ve seen the chimney.
Reading the Warning Signs
Crumbling mortar between bricks lets water in, and once it freezes into the brick face it starts to spall. White staining is often a sign of moisture moving through the masonry. Catching it before bricks loosen keeps the repair smaller.
How the Repair Comes Together
We clear out failed joints, repoint with mortar matched to the existing brick, and reset any bricks that have come loose. Any cap, crown, or flashing work is coordinated in the same visit so the top of the chimney ends up fully sealed. A camera check confirms the inside is sound before we close it out.
Brands We Service
We work with DuraFlex liner systems and know where they wear at the appliance collar and along the flue length, which is where most liner issues start. We install HeatShield resurfacing and know how it cures against a cleaned flue surface, and we fit Gelco caps built to hold up over years of humidity and sun. Olympia Chimney components round out the professional-tier materials we specify on repair work.
We also service existing installations from Copperfield and Famco, and we’re comfortable working with whatever professional-tier product is already in your chimney. Whether you have DuraFlex, HeatShield, Gelco, Olympia Chimney, Famco, Copperfield, or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Smoke spilling into the room. Smoke that won’t go up the flue usually means a blocked flue or a liner problem. It’s worth stopping use and having it checked before the next burn.
- Water stains near the chimney. Stains on the ceiling, wall, or attic near the chimney point to flashing, cap, or crown failure. Water that gets in keeps traveling until the source is sealed.
- A smoky odor between fires. Lingering creosote smell or a musty draft when the fireplace is idle often points to soot buildup, a missing cap, or a flue that’s pulling moisture. A sweep and camera check usually explains it.
- Crumbling mortar or loose bricks. Flaking mortar and shifting bricks mean the masonry is losing its grip. Left alone, it gets more expensive to repair than it would be now.
- Carbon monoxide concerns. If a carbon monoxide alarm sounds and the chimney is part of your home’s venting, stop using the appliance and have the flue inspected. CO is colorless and odorless, and a compromised flue is one reason it can build up.
Our Process, Step by Step
- 1
Call and book. You call (844) 834-5492, we answer 24/7, and we book a window with fast dispatch from 7am to 7pm. We ask about the symptoms, the age of the home, and what appliances the chimney vents.
- 2
Diagnose with a camera. We run a camera down the flue and inspect the cap, crown, flashing, and masonry. Everything gets photographed so you can see what we see, not just take our word for it.
- 3
Explain what we found. We walk through the footage with you and describe the repair that fits, in plain language. If work can wait, we say so.
- 4
Written estimate. You get a flat-price estimate that sets the final price, agreed before any work begins. No surprises after the job starts.
- 5
Complete the repair. Our technicians complete the repair with the professional-tier materials named in the estimate. When it’s done, you get a photo report of the finished work.
How Much Does Chimney Repair Cost in Coral Springs?
Chimney repair cost in Coral Springs typically runs from $250 for a straightforward cap installation up to $4,500 for a full liner replacement, and most jobs land in between. A typical cap installation runs $250-$550 depending on flue count and style. A chimney flashing repair in Coral Springs runs $300-$800, a crown repair $350-$900, and masonry repair $500-$2,500. Liner work is the largest item, running $1,800-$4,500 depending on flue height and liner diameter.
What affects the price most is how much of the chimney is actually involved. Access height, the number of flues, whether the crown has to be rebuilt or sealed, and whether the masonry needs repointing all move the number. Material choice matters too: a HeatShield resurfacing job often brings a liner back into service at less than a full DuraFlex replacement when the damage doesn’t call for starting over.
The way to avoid overpaying is to get the diagnosis before the quote. A camera inspection and photo report let you see exactly what a repair is for, so you can compare bids on equal footing. Every recommendation we make is tied to what the footage shows, and if a problem can safely wait until the next season, we’ll tell you that instead of pressing the work.
Our free estimate includes the inspection footage, the written flat price, and a clear explanation of what’s included. Nothing gets added after the estimate is signed. Call (844) 834-5492 for an exact quote – estimates are free.
Our Service Area Near Coral Springs
We serve Coral Springs along with the surrounding communities of Margate, Parkland, Tamarac, North Lauderdale, Coconut Creek, San Castle, Hypoluxo, Seminole Manor, and Highland Beach. Travel between these nearby cities means a booked visit is scheduled quickly, and same-day repair is often available when you call early in the day. Whether you need Carrington Chimney Sweep for a cap, a chimney repair consultation, or a full inspection before a real-estate closing, we can get you on the schedule.
Serving Coral Springs, FL – Our Local Coverage Area
We serve Coral Springs and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions About Chimney Repair in Coral Springs
Chimney repair covers any work that restores the chimney’s structure or its ability to vent safely, from a cap or crown fix to a liner replacement or masonry repointing. It’s separate from a routine sweep, which is cleaning, though the two often happen in the same visit when a sweep turns up damage. We diagnose with a camera first, then recommend only the repair the evidence supports. Call (844) 834-5492 if you’re not sure which you need – we’ll sort it out.
Most cap, flashing, and crown repairs finish in a single visit. Liner installations and larger masonry work usually take longer and may need a second appointment depending on access and material. The exact timeline is spelled out in your written estimate before we start. Call (844) 834-5492 and we can give you a realistic estimate for your chimney.
Most chimney repairs in Coral Springs range from $250 for a cap job to $4,500 for a full liner replacement, with flashing, crown, and masonry work landing in the $300-$2,500 range. The final figure depends on how much of the chimney is involved and which materials the repair calls for. Every estimate is free and flat-priced. Call (844) 834-5492 for an exact quote.
Yes – we install and service DuraFlex liner systems and apply HeatShield resurfacing, along with Gelco caps, Olympia Chimney components, and Famco venting. We know where these products tend to wear and how to restore them without starting from scratch when resurfacing fits. Whether you already have a DuraFlex flue or you’re considering one, we can walk you through the options. Call (844) 834-5492 to book an inspection.
Same-day repair is often available when you call early, and we answer the phone 24/7. Dispatch runs from 7am to 7pm, Sunday through Friday, and we’re closed on Saturday; a call outside dispatch hours is booked into the next opening. When we arrive, we diagnose before we quote. Call (844) 834-5492 to book.
The materials we install carry their own manufacturer warranties, and our repair work is backed by a satisfaction guarantee, spelled out in your written estimate. If something isn’t right after a repair, we want to know about it. Call (844) 834-5492 to talk through any concern.
Clear the hearth and the area in front of the fireplace, move anything breakable away, and make sure we can get to the roof access point. If you have a fireplace insert or a gas appliance in the chimney, let us know when you book so we bring the right tooling. Call (844) 834-5492 and we’ll note it on your appointment.
Schedule Your Chimney Repair Service in Coral Springs Today
If a cap is loose, a crown is cracked, or you’ve been putting off a smoky smell, the fix is a phone call away. We diagnose with a camera, quote a flat price in writing, and only recommend work the evidence supports. Call (844) 834-5492 for a free, no-obligation estimate. We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday.
Written by the team at Carrington Chimney Sweep.